A leaking dishwasher costs $100 to $250 to repair in most cases, and the average dishwasher repair is about $200 (Angi, 2026). The most common cause is a worn door gasket, which costs $100 to $250 to replace. Stop the machine, mop up, and check the gasket, filter, and detergent first. Those free checks fix most leaks.
Safety first
- Stop the cycle and turn the dishwasher off as soon as you see a leak. Do not keep running it to “see how bad it gets”. Every minute adds water to the floor and the cabinets.
- Turn off the power at the breaker before you reach underneath the dishwasher or remove the lower access panel. Water and live wiring do not mix, and the pump, motor, and inlet valve all sit in the wet zone under the tub.
- Turn off the water supply to the dishwasher before you disconnect any hose or valve. The shutoff is usually under the kitchen sink, on the hot-water line feeding the dishwasher.
- Mop up standing water right away and dry the area. Water that sits under a dishwasher soaks into the subfloor and breeds mold. If the floor is already swollen, warped, or soft, or water has leaked through to the ceiling below, call a water-damage restoration pro, Angi puts gray-water restoration at about $5.25 per square foot (Angi, 2026).
- Never pour chemical drain cleaners into a dishwasher. They do not fix leaks, they damage seals and hoses, and they leave caustic residue in a machine that washes your dishes.
- If water has reached an electrical outlet, the dishwasher’s power cord, or the breaker panel, do not touch anything wet. Turn off the breaker from a dry position and call a pro.
Tools you’ll need
- Towels and a bucket, for the water that is already on the floor, and for the small amount that comes out when you disconnect a hose (causes 4 and 7) or pull the filter (cause 3).
- Flashlight, to see the gasket, the hoses, and the pump area under the machine.
- Screwdriver, to remove the lower access panel (kick plate) and to tighten a loose hose clamp.
- Adjustable wrench, to tighten or replace hose connections and the water inlet valve.
- Level, a small torpedo level to check whether the dishwasher sits level (cause 5).
- Mild soap, warm water, and white vinegar, to clean the door gasket and the filter.
- Replacement parts, bought by your dishwasher’s exact model number, a door gasket, drain hose, latch, or inlet valve, if the diagnosis points at one.
The causes, ranked most likely first
1. Damaged or dirty door gasket, the most common cause
How to tell: Water leaks from the front of the dishwasher, along the bottom edge of the door, usually during the wash or rinse cycle. The gasket is the rubber seal around the door frame, and when it is worn, torn, flattened, or caked in grease, it cannot seal against the tub. You can see the problem by running a finger along the gasket: if it feels hard, brittle, or has visible cracks, tears, or flattened spots, it is done. A gasket caked in grease or food can look failed when it is only dirty, but a torn, flattened, or hardened gasket cannot seal, and it is time to replace it.
The fix: Open the door and wipe the gasket all the way around with warm soapy water and white vinegar. If it is dirty but intact, clean it, close the door firmly, and run a short cycle to see if the leak is gone. If it is torn, flattened, or hardened, replace it: buy the gasket by your dishwasher’s exact model number, pull the old one out of its channel (it usually just pulls out, no tools needed), and press the new one in, working it evenly into the groove all the way around. Warming the new seal in hot water for a few minutes makes it more flexible and easier to seat.
Cost: A door gasket part costs about $50 to $150 (Fixr, via Appliance Repair Menifee, 2026), or $50 to $100 (HouseTuned, 2026). A pro door gasket replacement typically costs $100 to $250 (Almwell, 2026), $120 to $275 (Appliances Calgary Repair, 2026), or $150 to $280 (Canadian Appliance Service, 2026).
2. Wrong detergent or too many suds, the free check
How to tell: The leak appears during the wash cycle, often with visible foam or suds spilling out the bottom of the door. The dishwasher is over-sudsing, and the foam pushes water out through the seal, even a healthy gasket cannot hold back a tub full of foam. This is common when someone has used regular dish soap or hand-washing liquid in the dishwasher instead of dishwasher detergent, or simply used too much detergent.
The fix: Stop using dish soap or hand-washing liquid in the dishwasher, only use dishwasher detergent, in the amount the box calls for. If the machine is full of foam right now, scoop out as much as you can, wipe the door seal, and run a rinse cycle with no detergent, then watch the door, if the leak is gone, the detergent was the problem. Do not add more detergent to “fix” a foaming machine, it makes the problem worse.
Cost: $0. If detergent was the problem, there is nothing to buy and nothing to replace.
3. Clogged filter, water backs up and overflows
How to tell: Water pools at the bottom of the tub, drains slowly, or trickles out of the door during the cycle. The filter at the bottom of the tub is clogged with food debris, grease, and mineral scale, so water cannot drain as it should during the cycle, it backs up and spills out instead. This is the same filter from the site’s dishwasher not draining guide, but here the symptom is a leak, not a full tub.
The fix: Pull out the bottom rack, twist out the filter from the floor of the tub (it usually twists counterclockwise), and rinse it under hot running water with a soft brush. Clear any food debris from the drain area around it, then put the filter back, making sure it locks in place, a filter that is not seated correctly lets debris through and can leak at the base. Run a rinse cycle and watch the door. If the leak is gone, the filter was the problem.
Cost: $0 for cleaning. A replacement filter costs about $50 to $125 if yours is cracked or warped. A pro filter cleaning as part of a service call typically costs $80 to $150 (AbodeRight, 2026).
4. Loose or damaged hoses, supply line or drain hose
How to tell: Water pools under the dishwasher, toward the back or underneath the cabinet, rather than at the front door. The supply hose (hot water in) and the drain hose (water out) both run under the machine, and both can leak. Connections loosen or corrode over time, and hoses crack, kink, or get punctured, a stray piece of glass or a rodent can do it, and a failed hose can release a large amount of water fast. If the leak is at a fitting, tightening it may be enough; if the hose itself is cracked, kinked, or swollen, it needs replacing.
The fix: Turn off the power at the breaker and the water supply under the sink. Remove the lower access panel (kick plate) and look at the hose connections with a flashlight. Tighten any loose fitting with an adjustable wrench, but do not over-tighten, a cracked fitting leaks worse than a loose one. If a hose is damaged, replace it by model number: disconnect both ends, take the old hose with you to match the length and fittings, and refit the new one, making sure the clamps are seated and tight. After refitting, turn the water back on and run a short cycle, watching the connections for drips.
Cost: A replacement drain or supply hose is an inexpensive part; a pro hose repair typically costs $100 to $250 (Angi, 2026). A new drain hose installed by a pro typically costs $150 to $300 (Canadian Appliance Service, 2026).
5. Door latch not closing fully, the seal never compresses
How to tell: Water leaks from the bottom of the door even though the gasket looks intact. The door latch is not pulling the door tight against the seal, so the gasket never compresses fully and water escapes at the bottom. If it is bent, loose, or broken, the door never compresses the seal fully, and water runs down the sides and looks like a leak from the gasket.
The fix: First check that nothing inside is blocking the door, a tall item or a rack that is not pushed in all the way. A tall pan or utensil blocking the spray arm can also push water at the seal, so check the loading too. If the latch itself is the problem, test it by closing the door and listening for a firm click. If the click is weak or absent, the latch is worn. A bent latch can sometimes be straightened, but a broken one needs replacing, buy it by model number, and most latches are a simple swap with a screwdriver once the inner door panel is off. Leveling means unplugging the machine, pulling it out, and adjusting the feet, then re-securing it to the counter, if that sounds like more than you want to take on, it is a short pro visit.
Cost: A door latch part is inexpensive; a pro latch or gasket repair typically costs $100 to $250 (Almwell, 2026), or $150 to $280 (Canadian Appliance Service, 2026).
6. Stuck float or failed float switch, the tub overfills
How to tell: The tub fills with too much water, the water level sits above the heating element at the bottom of the tub, or water keeps entering after the fill should have stopped, and then it spills out the bottom of the door. The float is the small device that tells the dishwasher when the tub is full. If the float is stuck down by debris or grease, or the switch has failed, the board never gets the signal to stop filling.
The fix: Find the float inside the tub, usually a mushroom-shaped piece near a front corner. Lift it up and down by hand; it should move freely and click as it rises and falls. If it is stuck, clean around it with warm water and mild soap, and check for debris underneath. If it moves freely but the tub still overfills, the float switch underneath has likely failed. Replacing a float switch means removing the lower access panel and swapping a small switch, a $150 to $300 minor repair including parts and labor if you have a pro do it (AbodeRight, 2026).
Cost: A pro float-switch repair typically costs $150 to $300 including parts and labor (AbodeRight, 2026). A float switch part costs $50 to $125 (HouseTuned, 2026).
7. Faulty water inlet valve, water keeps entering or leaks at the connection
How to tell: Water leaks from underneath or behind the dishwasher, near where the supply hose connects, or water keeps trickling into the tub even when the dishwasher is off. The inlet valve is the electric valve that lets hot water into the machine, and when its seal fails or its screen clogs, it can leak at the connection or let water in when it should be closed. This is the valve to suspect when the hoses are sound but water still appears under the machine.
The fix: Turn off the power at the breaker and the water supply under the sink. The valve is usually at the lower left or right, behind the access panel, where the supply hose connects. Check whether the leak is at a loose fitting, that can just be tightened. If the valve itself is leaking or it will not shut off, it needs replacing. Replacing an inlet valve is a pro job for most homeowners: it means working with the water supply line and the valve’s electrical connection. Check the valve’s inlet screen for mineral deposits while you are there, hard water clogs it and can cause the same overfill symptoms as a stuck float.
Cost: An inlet valve part costs about $54 to $55 (HouseTuned, 2026), or $75 to $150 (HomeAdvisor, 2026). A pro inlet valve replacement typically costs $130 to $180 (HouseTuned, 2026), or $150 to $300 (Almwell, 2026).
8. Worn pump seal or cracked tub, pro-only, and the replace decision
How to tell: Everything else checks out, the gasket is sound, the detergent is right, the filter is clean, the hoses are tight, the float moves freely, but water still pools under the center or rear of the machine. The pump seal, where the motor shaft enters the tub, is worn and letting water through, or the tub itself is cracked or corroded. A cracked spray arm can also throw water at the seal and look like a gasket leak, so check the spray arms for cracks first. A cracked or corroded tub is the worst version: like a cup with a hole in it, it cannot be patched reliably.
The fix: None for a homeowner on the pump seal, reaching it means pulling the dishwasher out of its cabinet, tipping it, and opening the pump assembly. A cracked spray arm is a simple DIY swap, but a pump seal or a tub is not. If the tub is leaking, or the pump seal has failed on a dishwasher past about 7 years old, get a quote and compare it against replacement before you approve anything, that is the repair-or-replace math below.
Cost: A drain pump replacement typically costs $150 to $350 including parts and labor (Almwell, 2026); a circulation pump and motor repair typically costs $230 to $430 (HouseTuned, 2026), or $200 to $500 for a motor repair (Fixr, via Appliance Repair Menifee, 2026). A cracked tub usually means replacing the dishwasher.
When to call a pro
Call an appliance repair tech. Do not keep troubleshooting if:
- Water has leaked through to the ceiling below, the subfloor is swollen or soft, or there is visible mold. That is water-damage restoration, not an appliance repair.
- Water has reached an electrical outlet, the power cord, or the breaker panel.
- The leak is coming from the pump seal or the circulation pump, which means pulling the dishwasher out of its cabinet.
- The tub is cracked or corroded. A tub repair costs more than the dishwasher is worth on most older units (Angi, 2026).
- You have worked through causes 1 to 7 and the leak is still there, the source is internal, and a tech with the machine pulled out will find it in one visit.
- The dishwasher is still under warranty. Opening it yourself can void the warranty, check the terms before you touch anything beyond the free checks.
What a pro typically costs
These are typical 2026 ranges. Angi’s national average for a dishwasher repair is about $200, with most homeowners paying $175 to $325 and the full range running $75 to $600 (updated Oct 21, 2026). Almwell puts a service call and diagnosis at $100 to $200, often applied to the repair (published Oct 30, 2026). Ask whether the diagnostic fee is applied to the repair before you approve the work.
| Repair | What a pro typically costs |
|---|---|
| Diagnostic visit / service call | $80 to $150 (AbodeRight, 2026); $100–$200 (Almwell, 2026); $90–$130 (HouseTuned, 2026) |
| Leak repair (seals, hoses, or tub cracks) | $100 to $250 (Angi, 2026) |
| Door gasket replacement | $100 to $250 (Almwell, 2026); $120–$275 (Appliances Calgary Repair, 2026); $150–$280 (Canadian Appliance Service, 2026) |
| Door latch replacement | $100 to $250 (Almwell, 2026); $150–$280 (Canadian Appliance Service, 2026) |
| Minor repair (latch, spray arm, gasket, float switch) | $150 to $300 including parts and labor (AbodeRight, 2026) |
| Water inlet valve replacement | $130 to $180 (HouseTuned, 2026); $150–$300 (Almwell, 2026); $160–$300 (Canadian Appliance Service, 2026) |
| Drain pump replacement | $150 to $350 (Almwell, 2026); $100–$250 (Fixr, via Appliance Repair Menifee, 2026) |
| Circulation pump / motor replacement | $230 to $430 (HouseTuned, 2026); $200–$500 (Fixr, via Appliance Repair Menifee, 2026); $320–$520 (Canadian Appliance Service, 2026) |
| Major component repair (pump motor or control board) | $300 to $650 (AbodeRight, 2026) |
| Control board replacement | $240 to $330 (HouseTuned, 2026); $250–$500 (Almwell, 2026) |
| New standard 24-inch built-in dishwasher, installed | $400 to $1,200 (Angi, 2026); $600–$1,800 including haul-away (Almwell, 2026); $790–$1,690 (HouseTuned, 2026) |
Repair or replace?
- Repair it if the dishwasher is under about 7 years old and the fix is a single common part, a door gasket, latch, inlet valve, float switch, or drain pump. Most of these cost $100 to $350 all-in, a small fraction of a new dishwasher (Almwell, 2026).
- Replace it if the tub is leaking, at any age (Almwell, 2026), or if the repair costs more than half the price of a comparable new dishwasher (Angi, 2026). Consumer Reports members paid a median of $855 for a new dishwasher from 2023 to 2025, which puts half at roughly $430 (via Appliance Repair Menifee, 2026). A $300 to $650 pump or control-board repair on a dishwasher past 7 years old is usually money better put toward a new one.
- Check the warranty first. Many dishwashers carry longer parts warranties on specific components. A failed part on a 3-year-old dishwasher may be covered even when the general warranty has expired.
- Check your home warranty and insurance. Angi notes a home warranty policy often covers dishwasher replacement, and homeowners insurance may cover the water damage a leak causes, but neither pays for the leak itself if you keep running the machine after you spotted it.
FAQ
Why is my dishwasher leaking from the bottom of the door?
Almost always a worn or dirty door gasket, a door latch that does not close fully, a cracked spray arm throwing water at the seal, or too many suds from the wrong detergent. Start with the gasket: wipe it clean, look for tears or flattened spots, and replace it if it is damaged. Then check the detergent.
Why is my dishwasher leaking underneath?
Water pooling under the center or rear of the machine usually comes from the drain hose, the water supply line, the inlet valve, or the pump seal. Check the hose connections first, they loosen and corrode over time. If the hoses are sound, the inlet valve or the pump seal is the next suspect, and both are pro jobs on most machines.
Can I still use my dishwasher if it is leaking?
No. Turn it off, mop up the water, and find the source before you run it again. Every cycle adds water to the floor, the cabinets, and the subfloor, and a small leak becomes a mold and water-damage problem fast.
How much does it cost to fix a leaking dishwasher?
A leak repair typically costs $100 to $250 (Angi, 2026), and the average dishwasher repair overall is about $200 (Angi, 2026). A gasket or latch runs $100 to $250, an inlet valve $130 to $300, and a drain pump $150 to $350. A pump motor or control board is $300 to $650, which is where the repair-or-replace math starts to favor a new dishwasher.
How long do dishwashers last?
The average lifespan of a dishwasher is typically 10 to 15 years (Angi, 2026). Almwell puts it at about 9 to 12 years, and recommends replacing a dishwasher after 10 to 12 years, or whenever it starts having repeated issues (Angi, 2026). A tub leak at any age is usually a replace, not a repair.
Why is there water on the floor after the dishwasher finishes, but not during the cycle?
A slow leak often shows up only after the cycle, when water left in the sump or a hose drains out onto the floor. Check the drain hose connection and the pump seal, both leak slowly enough to go unnoticed during the cycle and pool afterward. Also check that the dishwasher is level: an unlevel machine lets water sit on one side and spill over after the cycle ends.
Sources: Angi, “Dishwasher Leaking from Bottom: How to Fix It” (updated Jul 8, 2026; damaged gasket most common cause; gasket, latch, filter, hoses, inlet valve, tub, detergent, leveling, pump causes; repair average; standard 24-inch built-in $400–$1,200; countertop $200–$500; gray-water restoration about $5.25 per sq ft; lifespan 10–15 years; replace after 10–12 years); Angi, “How Much Does Dishwasher Repair Cost? [2026 Data]” (updated Oct 21, 2026; $75–$600 range, most pay around $225, typical 2026 range $175–$325, leak repair $100–$250); Whirlpool, “Dishwasher Leaking Troubleshooting Guide” (common causes: door gasket, inlet valve, float assembly, pump/motor seals, loose connections, cracked spray arm, worn tub causes); “First American Home Warranty, “Dishwasher Leaking? Here’s Why and How to Fix It” (door seal, hoses, inlet valve, float assembly, pump/motor seals, loose connections, cracked spray arm, worn tub causes); ”
lmwell, “Repair or Replace a Dishwasher? The Age & Price Test (2026 Costs)” (published Oct 30, 2026; service call $100–$200; latch and gasket $100–$250; inlet valve $130–$300; drain pump $150–$350; control board $250–$500; new dishwasher $600–$1,800; repair under about 7 years unless tub is leaking; 50% rule); AbodeRight, “How Long Does Dishwasher Repair Take?” (costs checked Aug 25, 2026; diagnostic $80–$150; minor repair $150–$300 incl. parts and labor; major component $300–$650; overall $150–$3450; averaging $250); HouseTuned, “How to Fix a Maytag Dishwasher Leaking” (published Sep 21, 2026, verified Oct 9, 2026; diagnostic $90–$130; drain pump $100–$230; part $21–$100; inlet valve $130–$180; $54–$55; control board $240–$330; circulation pump $230–$430; new 24-inch built-in $790–$1,690 with delivery, installation, and haul-away); Appliance Repair Menifee, “Is It Worth Repairing a 7-Year-Old Dishwasher?” (Oct 23, 2026; Fixr filter $50–$125; gasket $50–$100; door spring $50–$150; soap dispenser $50–$80; HomeAdvisor inlet valve $75–$150, drain pump $150–$340; Fixr drain pump $100–$250; motor $200–$350; Consumer Reports median new dishwasher $855, 2023–2025; median repair $142; 50% rule); ”
EngineerFix, “Why Is My Dishwasher Leaking From the Bottom of the Door?” (door gasket compression set, latch preload, over-sudsing, stuck float switch overfill); Same Day Appliance Repair, “Dishwasher Repair Calgary Cost” (2026; door gasket or seal 120–$275; inlet valve 150–$330; drain pump 210–$375+); Canadian Appliance Service, “How Much Does Dishwasher Repair Cost in Vaughan?” (2026; gasket $150–$280; inlet valve $150–$300; drain pump $220–$350);

Leave a Reply