A water heater repair costs $616 on average, with most homeowners paying $228 to $1,018 (Angi and HomeAdvisor, 2026). But no hot water is usually a free fix: a tripped breaker, a blown-out pilot light, or a tripped high-limit switch. Check those three first. They take minutes and fix the problem more often than any part replacement.
Safety first
- If you smell gas, leave the house and call your gas utility or 911 from outside. Do not relight a pilot light, flip switches, or use your phone inside.
- Never restore power to an electric water heater while the tank is empty. A heating element exposed to air burns out in seconds.
- Gas burner, gas valve, and gas line work is pro-only. The DIY steps below cover checks and resets only.
- Turn power off at the breaker before removing any access panel on an electric unit, and verify it is off before touching wires.
Tools you’ll need
- Flashlight, to see the pilot light window and the access panels in a dark closet or garage.
- Screwdriver (flathead), to remove the electric unit’s access panels.
- Multimeter, to test a heating element or thermostat for continuity (cause 5). Only if you are comfortable testing live circuits with the power off and verified off.
- Long lighter or fireplace match, to relight a pilot light on a gas unit that has a manual ignition (cause 3). Many newer units have a push-button igniter instead.
- Garden hose, for flushing the tank (cause 6). A short one is fine; a long one is better if your drain is far from the tank.
- Bucket and towels, for the small amount of water that comes out when you drain or flush.
The causes, ranked most likely first
1. Tripped breaker or blown fuse (electric only)
How to tell: The water heater has no power at all. No indicator light, no hum, nothing.
The fix: Go to your breaker panel and find the breaker labeled for the water heater. If it is tripped (sitting in the middle position), rock it fully to OFF, then back to ON. Wait 30 to 60 minutes and test a hot tap. If the breaker trips again immediately, stop. A breaker that will not stay on means a shorted heating element or a wiring fault. Call a pro.
Cost: Free if it is just a reset. A diagnostic visit to find out why a breaker keeps tripping typically costs $100 to $200.
2. Thermostat set too low or turned down
How to tell: The heater has power and the pilot is lit (gas) or the breaker is fine (electric), but the water never gets hot.
The fix: Check the thermostat setting. The U.S. Department of Energy recommends 120°F. If someone turned it down, after a vacation, a guest, a child, turn it back to 120°F and wait an hour. On an electric unit, check both thermostats (upper and lower) behind the access panels. They should both be set to 120°F.
Wait an hour and test a hot tap. A full tank takes 30 to 60 minutes to reheat.
Cost: Free. A pro thermostat replacement typically costs $150 to $200.
3. Pilot light is out (gas only)
How to tell: No hot water, and when you look through the pilot window at the bottom of the tank, there is no small blue flame.
The fix: Follow the relighting instructions printed on the label on your water heater, they vary slightly by model. Do not guess.
In general: turn the gas control knob to PILOT, hold it down, and press the igniter button (or hold a long lighter to the pilot) until the pilot lights. Keep holding the knob for 30 to 60 seconds, then turn it to ON.
If the pilot lights but goes out when you release the knob, the thermocouple is the likely culprit. See cause 4.
If you smell gas at any point, stop, leave the house, and call your gas utility from outside.
Cost: Free if you relight it yourself. A pro pilot-light relight and inspection typically costs $100 to $200.
4. Failed thermocouple (gas only)
How to tell: The pilot lights when you hold the knob down, but it goes out the moment you release it. The thermocouple is the small copper probe sitting in the pilot flame; its job is to tell the gas valve the pilot is lit. When it fails, the valve shuts the gas off.
The fix: This is a part replacement, not a cleaning job. A universal thermocouple costs $15 to $25 at a hardware store, but replacing it means working on the gas valve assembly. If you are not comfortable with gas fittings, hire a pro, this is a short job for them.
Cost: A pro thermocouple replacement typically costs about $150, including parts and labor, and takes under an hour (Angi, 2026).
5. Tripped high-limit reset or failed heating element / thermostat (electric only)
How to tell: The breaker is fine and the thermostat is set correctly, but the water stays cold, or, in the classic tell: the water is lukewarm all the time (failed upper element) or hot water runs out very fast (failed lower element).
The fix:
Reset the high-limit switch first. Turn the power OFF at the breaker. Remove the upper access panel, take off the insulation and the plastic safety guard, and press the red reset button above the thermostat. Replace the guard, insulation, and panel, restore power, and wait an hour.
If the reset does not fix it, test the elements. With the power off and verified off, use a multimeter to test each heating element and thermostat for continuity. A failed element shows no continuity. This step is for homeowners comfortable with a multimeter; if you are not, this is where the DIY path ends and the pro path begins.
A failed element or thermostat is a parts swap for a pro, usually one visit.
Cost: A pro heating element replacement typically costs $200 to $300. A pro thermostat replacement typically costs $150 to $200 (Angi / HomeAdvisor, 2026). The parts themselves are cheap. An element runs $15 to $60 and a thermostat around $20, which is why this is one of the best-value pro visits on the list.
6. Sediment buildup in the tank
How to tell: This one usually causes lukewarm water or water that runs out fast rather than no hot water at all, but a heavy sediment layer can insulate the bottom of the tank so thoroughly that the burner or lower element cannot heat the water above it. Rumbling or popping noises from the tank are the giveaway.
The fix:
Turn the water heater off (gas to PILOT or OFF; electric off at the breaker).
Attach a garden hose to the drain valve at the bottom of the tank and run it to a floor drain or outside.
Open the valve and flush until the water runs clear. Close the valve, refill the tank completely, and restore power or gas.
Flush once a year from now on. The U.S. Department of Energy’s maintenance guidance lists annual flushing as the key step to prevent sediment buildup.
Cost: $0 if you do it yourself. A pro flush and descaling typically runs $150 to $350 as part of a service visit (Angi, 2026).
7. Failed gas control valve (gas only)
How to tell: The pilot is lit and stays lit, the thermostat is set correctly, but the burner never fires. You hear nothing when you turn up the thermostat, no whoosh, no burner sound.
The fix: None for a homeowner. The gas control valve is the combined thermostat and gas valve unit, and replacing it means working on the gas line, pro-only.
Cost: A gas control valve replacement typically costs around $350 installed, and can run $300 to $500 depending on the model (Angi, 2026).
When to call a pro
- You smell gas, or the pilot will not stay lit after a few tries.
- The breaker trips again as soon as you reset it, or you see scorch marks, melted wires, or water damage around the unit.
- The tank is leaking. A leaking tank cannot be repaired; it needs replacing.
- The water is rusty or the tank is over 10 years old and needs a major repair. Use the site’s half-price rule: if the repair costs more than half the price of a comparable new water heater, replace it.
- Any step asks you to open a gas fitting or work on live wiring and you are not comfortable doing it. Stop there.
What a pro typically costs
These are typical 2026 ranges from Angi and HomeAdvisor contractor data (national average repair $616; most homeowners pay $228 to $1,018). Your area and the exact cause will move the number. Ask whether the diagnostic fee is applied to the repair before you approve the work.
| Repair | What a pro typically costs |
|---|---|
| Diagnostic visit | $75 to $150 |
| Tripped breaker reset | $0 DIY; $75 to $150 for a diagnostic visit |
| Thermostat adjustment | $0 DIY; $75 to $150 for a diagnostic visit |
| Pilot light relight | $0 DIY; $100 to $200 for a pro relight and inspection |
| Thermocouple replacement | About $150, including parts and labor |
| Heating element replacement | $200 to $300 |
| Thermostat replacement | $150 to $200 |
| Gas control valve replacement | $300 to $500 |
Repair or replace?
Repair it if the tank is under 8 years old, the tank itself is not leaking, and the fix is a single part (element, thermostat, thermocouple, pilot).
Replace it if the tank is leaking, the tank is over 10 years old and needs a second major repair, or the repair quote is more than half the price of a new unit. A new tank-style water heater typically costs $850 to $1,800 installed (Angi, 2026).
Tankless is a different decision. Tankless units cost $1,400 to $3,900 installed and solve a different problem (endless hot water, not a broken tank). Do not let a repair quote turn into a tankless upsell unless you actually want one.
FAQ
Why is my water heater not producing hot water all of a sudden?
The most common sudden causes are a tripped breaker (electric), a pilot light that blew out (gas), or a tripped high-limit reset switch. All three are free checks that take minutes, which is why they top this guide. A failed heating element or thermocouple is the next most likely cause.
Why is my water only lukewarm, not cold?
On an electric unit, lukewarm water that never gets hotter usually means the upper heating element has failed. Hot water that starts hot and runs out fast usually means the lower element has failed. On a gas unit, lukewarm water with a lit pilot points to sediment buildup or a thermostat problem.
How long does it take for a water heater to reheat?
A full tank takes 30 to 60 minutes to reheat after a reset, a relight, or a thermostat change. Wait at least an hour before concluding the fix did not work.
What temperature should my water heater be set to?
120°F, per the U.S. Department of Energy. Higher settings waste energy and raise the scald risk; lower settings can leave you short on hot water and, in rare cases, allow bacteria to grow in the tank.
How much does a water heater repair cost?
The national average repair is $616, and most homeowners pay $228 to $1,018 (Angi and HomeAdvisor, 2026). A diagnostic visit runs $75 to $150, a heating element replacement $200 to $300, and a thermostat replacement $150 to $200.
Can I relight the pilot light myself?
Yes, if your unit has printed relighting instructions on its label, follow those exactly. If the pilot will not stay lit, or you smell gas, stop and call a pro.
My water heater is making rumbling noises. Is that related?
Yes. Rumbling or popping is sediment boiling at the bottom of the tank. Flush the tank (cause 6). If the noise continues after a flush, or the tank is over 10 years old, have a pro look at it.
How often should I flush my water heater?
About once a year, per the Department of Energy’s maintenance guidance. In hard-water areas, twice a year is worth it.
Sources: U.S. Department of Energy water heater maintenance guidance (120°F setting, annual flushing); Angi, “Cost to Repair a Hot Water Heater” (2026 data, updated Aug 24, 2026; national average $616, most pay $228–$1,018); HomeAdvisor water heater repair cost data (2026); The Spruce, “10 Common Water Heater Problems and Solutions” (troubleshooting sequence for no hot water, high-limit reset, element failure symptoms).

Leave a Reply